Tips and Techniques from Gander River Boat Builders

Timber

Juniper (Tamarack) is a strong softwood that grows mostly in wet swampy areas and is the preferred timber for the ribs of the Gander River Boat. Builders heat thin strips of juniper in steam or boiling water to make it pliable to bend the wood to the desired shape.

“I usually put about half a gallon of Javex in the water with it. That makes the juniper pretty soft.” – Eugene Saunders, Glenwood

Var (Balsam Fir) is the most common species in Newfoundland and grows best in moist well-drained soils. As a strong and light softwood, fir was once preferred for planking a Gander Bay Boat but its susceptibility to insect attacks has damaged the quality of timber. As a result, many builders have been forced to switch to spruce as an alternative.

“That’s all we used to use one time, but then we switched to spruce because we couldn’t get var. It seemed like the spruce didn’t last as long as what the var did, so I went back. I built one last spring with var, but she might not last either. They say the wood is no good.” – Basil Gillingham, Gander Bay

Spruce is a relatively light softwood that has become the preferred timber for the plank, stem, sternpost and keel in a Gander River Boat since fir populations have been damaged by invasive insects.

“Fir is easier to work with than spruce, it’s a softer wood.” – Ern Hodder, Gander Bay

Caulking

Cotton string is preferred for sealing the planks in a Gander River Boat, but local builders find it increasingly difficult to find. Some builders have turned to using an ordinary house mop as a substitute. Once taken apart, the individual strand are inserted between planks using a caulking iron and mallet.

“The strands are five to six feet long when it’s taken apart. One mop does a boat.” – Ern Hodder

When the motor was removed from this Gander River Boat, the boat became leaky above her waterline. To reseal the seams, the owner filled the boat with water and left it overnight for the wood to plim.Paint

Gander River boats are always painted brown and white. White is selected for the exterior hull because it is the best colour for the wood when the boat is turned over on the shore. The light colour paint absorbs less sunlight and the wood does not dry out as quickly.

If the boat is left upright out of the water, the wood will dry and shrink and once she’s placed back in the water she will be leaky. After some time back in the water, the wood will plim (swell) and the seams will reseal.

When the motor was removed from this Gander River Boat, the boat became leaky above her waterline. To reseal the seams, the owner filled the boat with water and left it overnight for the wood to plim.

3 thoughts on “Tips and Techniques from Gander River Boat Builders

  • April 25, 2016 at 11:07 pm
    Permalink

    Love the site and info. I have used the Gander for nice while now. One of the boat my brother and I have is 22 years old and still working the gander river. I have always bought my boat used from the guides and now think I would like to try build my first. I have the mold and timbers but would like a good set of drawing. Could you please help.

    Reply
    • April 28, 2016 at 9:46 am
      Permalink

      Hi Kirk, we’ll be in touch with you soon via email.

      Reply
  • July 17, 2016 at 11:13 pm
    Permalink

    Hi, I love your site. I am a carpenter but never built a boat. For the last 11 years I have been fishing the Gander River with a friend who owns a Gander River Boat. The past three years I have been learning the River. I would love to build a Gander River Boat, could you send me the drawings, and more information on building the molds? I have a steamer made for making sled runners, skis, and chairs. Would love to build a Gander River Boat this winter. I appreciate any helpful advice you could offer. Thanks very much.

    Reply

Leave a Reply to Philip Healey Cancel reply

Your email address will not be published. Required fields are marked *